I have 2 paslode cordless nail guns framer and finish nailers Since I’m not a framer, I’ll happily take the smaller nail capacity in exchange for a lighter tool that’s easier to use and less of a work-out on my arm.I figure there are a lot of contractors who hang out here If Paslode’s mission was to create a light, manageable, easy-to-use framing gun, they’ve succeeded. I’ve used plenty of other guns that can make the switch with a little button or a toggle and it’s a mystery why Paslode hasn’t done something similar.īut like I said, these are minor problems at best. I tend to keep my framing guns on sequential fire for safety reasons, but it would be nice to be able to quickly toggle back and forth if I needed it. Basically, if you drop it, you’ve lost it. And once this O-ring is released from the tool, it can be easily lost on a construction site. The only way I’ve found to do it is with the point of a utility knife, which puts the O-ring in considerable danger. The process involves slightly relocating the angle of the trigger, but in order to do that you first have to remove a nearly microscopic O-ring that holds the trigger in place. The other negative is the toggle between sequential and bump fire modes. It’s a small point, but whenever I get a Paslode gun, I end up having to pillage the connector off another air tool until I can get back to the hardware store to get a new one. I understand there are a lot of people who use ¼-inch connections, but it seems like every other manufacturer supplies a ¼-inch male coupling with the tool. I have only a couple of complaints about the tool, and they are incredibly minor.įirst, like all Paslode guns, the F325R does not come with an attached ¼-inch male air-hose coupler. This serves as protection when the gun is placed on a finished surface. I also like how the rubber overmold on the handle extends up and forms a ring around the body of the tool. The nose of the gun is similar to other Paslode nailers I’ve used with a very aggressive claw and a large “glove-friendly” depth-of-drive adjustment. The large rafter hook works great and can be switched to the other side of the tool with just a hex key it’s big and deep enough to be hung off of a 2-by rafter without any problem. The F325R has a couple of other features that I liked. I’ll still keep the larger gun for production work, but for most daily tasks, I’ll stick with the new Paslode. On a framing crew, this isn’t going to last long, but if you spend your time boxing out for medicine cabinets and reframing door openings, the reloading isn’t as constant and I never thought of it as a nuisance. Regular paper-tape guns traditionally hold three racks of nails, but the Paslode holds only one, amounting to about 40 nails at a time. The only real sacrifice for this compact size is nail capacity. As a test, I even unloaded about 20 nails in fast sequence into a PT 6圆 and every nail went in below the surface of the wood. I knew I'd have no problems nailing regular 2x stock, but the gun performed just as well when I worked with LVLs and pressure-treated lumber. I was happy to learn that the size reduction doesn't cause any loss of power. When I’m working, the smaller magazine doesn’t get hooked on the air hose like the larger ones. At less than 13 inches long, it fits in a stud bay with room to spare, and the short nail magazine makes it more maneuverable in corners and closets where clearances are tight. The reduced weight is nice, but what I really like about this gun is the size. According to Paslode, much of this weight reduction is because they made the body out of magnesium instead of the usual aluminum. And at just under 6 pounds, it’s a good 2 pounds lighter than the average stick framer (my old Bostitch gun is over 8 pounds). I’ve found it to be a great tool to have on hand, especially for remodeling tasksĪs framing guns go, the F325R is small-really small. In fact, it’s actually smaller than some of my finish guns. For the past several weeks I’ve been testing out Paslode’s new F325R Compact Framing Nailer, and it’s nothing at all like my old framing guns. The pin is held on by a small O-ring-which if dropped will almost certainly be lost.įraming guns are big and heavy tools. Doug Mahoney Changing between bump and sequential means repositioning the pin that secures the trigger.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |